Page 1 of 2
Hi
Posted: 28 Oct 2020, 18:48
by Thomas1402
Hi @ all,
my name ist Thomas. I´m an engineer of automotive electronics from Zwickau/Germany. At work and as a hobby I design PCB, build and program them. Over the next months I´d like to create a gateway between Android head units and the Ford Convers+.
Re: Hi
Posted: 29 Oct 2020, 10:00
by Syntax
Hello and welcome.
This sounds great, I have always wanted to try Android unit instead of MCA but the bad communication with the car discouraged me.
Looking forward to see your work.
Re: Hi
Posted: 15 Nov 2020, 11:35
by Gwe89
Thomas1402 wrote: ↑28 Oct 2020, 18:48
Hi @ all,
my name ist Thomas. I´m an engineer of automotive electronics from Zwickau/Germany. At work and as a hobby I design PCB, build and program them. Over the next months I´d like to create a gateway between Android head units and the Ford Convers+.
Hi can you make pcb if we had the design for you
Re: Hi
Posted: 15 Nov 2020, 12:45
by Go4IT
Gwe89 wrote: ↑15 Nov 2020, 11:35
Hi can you make pcb if we had the design for you
Would you explain what you think about? You have a schematic and want him to place parts and route lanes/vias? Or producing the PCB?
Re: Hi
Posted: 15 Nov 2020, 14:38
by Gwe89
I have a ardunio Leonardo canbus board but its only 1 chanel, could be redesigned to have 2 canbus channels then could do away with my nano and the 2 mcp2515
https://www.hobbytronics.co.uk/leonardo ... qvEALw_wcB
Re: Hi
Posted: 15 Nov 2020, 14:42
by Gwe89
Here is the schematic for it but wouldn't know how to make new with 2 can channels
Re: Hi
Posted: 17 Nov 2020, 17:20
by Thomas1402
Gwe89 wrote: ↑15 Nov 2020, 11:35
Hi can you make pcb if we had the design for you
Hi Gwe89,
unfortunately I can´t see your appendix yet. Do you need the design for two CAN channels with MCP2515?
Re: Hi
Posted: 17 Nov 2020, 18:58
by Gwe89
Thomas1402 wrote: ↑17 Nov 2020, 17:20
Gwe89 wrote: ↑15 Nov 2020, 11:35
Hi can you make pcb if we had the design for you
Hi Gwe89,
unfortunately I can´t see your appendix yet. Do you need the design for two CAN channels with MCP2515?
Hi thanks for getting back to me, yes basically like the one iv posted here but with 2 can channels so would need both the can chips I think, the CS for this board is 17 and there's other pins available to use for CS
Re: Hi
Posted: 19 Nov 2020, 19:28
by Thomas1402
Gwe89 wrote: ↑17 Nov 2020, 18:58
Hi thanks for getting back to me, yes basically like the one iv posted here but with 2 can channels so would need both the can chips I think, the CS for this board is 17 and there's other pins available to use for CS
I received your PN, but cause I´m new, I can´t answer it...
Go4IT wrote: ↑15 Nov 2020, 12:45
Go4IT is it possible to activate my profile?
Re: Hi
Posted: 28 Nov 2020, 20:37
by Gwe89
Thomas1402 wrote: ↑19 Nov 2020, 19:28
Gwe89 wrote: ↑17 Nov 2020, 18:58
Hi thanks for getting back to me, yes basically like the one iv posted here but with 2 can channels so would need both the can chips I think, the CS for this board is 17 and there's other pins available to use for CS
I received your PN, but cause I´m new, I can´t answer it...
Go4IT wrote: ↑15 Nov 2020, 12:45
Go4IT is it possible to activate my profile?
Send me email if you still can't reply to my message
gwe1989@gmail.com