MicroHacker Forum

Posted: **10 Dec 2023, 16:48**

Hey folks, these days i got an non-starting MCA unit. It is the backend that has failed, the frontend is ok.
The untit draw about 110 mA at 12 V.

Even if RAMs are from week 44/2010 i've heated them up to see if they react, but no success.
Next i measured all the voltages and they are ok. I've reflashed the unit, once with an known running firmware and once with the same. Both could be programmed without a problem, so at least CPU and Flash seem ok.

At least i've swapped the Radio-Processor (V850, uPD70F3283) with a working MCA and can tell it's also not the problem. But the bad unit won't boot.

Now i'm, getting a little out of ideas... i once got a similar problem with an NX unit (see viewtopic.php?t=249) and couldn't solve this either.

If i only could get some debug messages out, why the firmware don't boot up.

Posted: **15 Dec 2023, 06:10**

I now again digged very deep into the system to find the cause of that error. As said, i can connect via JTAG to the OMAP and it looks like OMAP behaving fine, but when i halt the CPU and show the registers i see that it always get stuck in an ABORT at PC 0xFFFF000C, which is also the reset-vector of ABORT mode:

Code: Select all

J-Link: ARM9 CP15 Settings changed: 5327F from 78, MMU On, ICache On, DCache On
PC: (R15) = FFFF000C, CPSR = 000000D7 (ABORT mode, ARM FIQ dis. IRQ dis.)
Current:
     R0 =00000003, R1 =9014D818, R2 =2C28D86C, R3 =00070F7C
     R4 =90000014, R5 =2000FE28, R6 =00000000, R7 =0000001C
     R8 =00000040, R9 =FFF6FACD, R10=3BFF97FE, R11=00040034, R12=00000000
     R13=BBE9D6AB, R14=00000002, SPSR=000000F7
USR: R8 =00000040, R9 =FFF6FACD, R10=3BFF97FE, R11=00040034, R12=00000000
     R13=4BDFFB35, R14=FE7B70FF
FIQ: R8 =F819FD75, R9 =EBCD07F7, R10=F9DFA3D6, R11=F7FFAFF7, R12=CE7FBED9
     R13=F3FBFD73, R14=67EEFFF1, SPSR=00000010
IRQ: R13=FEBED7DA, R14=F46E7BFE, SPSR=00000010
SVC: R13=2000FE18, R14=00001FA0, SPSR=00000010
ABT: R13=BBE9D6AB, R14=00000002, SPSR=000000F7
UND: R13=9FF77F7B, R14=BF7DFFD1, SPSR=00000010

Connecting was easy using the Segger J-Link. Only keep in mind to prevent V850 to do watchdog-resets by pulling it's reset-line down (Tuareg mode) and once connected using J-Link (ARM9, LittleEndian, rest is default), also disable the OMAP watchdogs using:

Code: Select all

connect
halt
write4 0xFFFEC808 0xF5
write4 0xFFFEC808 0xA0
write4 0xFFFEB048 0xAAAA
write4 0xFFFEB048 0x5555

After that you can also single-step, set breakpoints, etc. and have all the time in the world to look at the results in memory or registers.

MicroHacker Forum

MCA backend won't boot

MCA backend won't boot

Re: MCA backend won't boot